Articles | Volume 16, issue 2
https://doi.org/10.5194/ms-16-325-2025
© Author(s) 2025. This work is distributed under
the Creative Commons Attribution 4.0 License.
the Creative Commons Attribution 4.0 License.
https://doi.org/10.5194/ms-16-325-2025
© Author(s) 2025. This work is distributed under
the Creative Commons Attribution 4.0 License.
the Creative Commons Attribution 4.0 License.
Research article
| 
11 Jul 2025
Research article |
| 11 Jul 2025
| 11 Jul 2025
A control strategy for shipboard stabilization platforms based on a fuzzy adaptive proportional–integral–derivative (PID) control architecture
Hongbo Liu
School of Mechanical and Power Engineering, Harbin University of Science and Technology, Harbin, 150080, China
Zhaobiao Zeng
School of Mechanical and Power Engineering, Harbin University of Science and Technology, Harbin, 150080, China
Xiaodong Yang
School of Mechanical and Power Engineering, Harbin University of Science and Technology, Harbin, 150080, China
Yuxin Zou
School of Mechanical and Power Engineering, Harbin University of Science and Technology, Harbin, 150080, China
Xianli Liu
CORRESPONDING AUTHOR
School of Mechanical and Power Engineering, Harbin University of Science and Technology, Harbin, 150080, China
Related subject area
Subject: Mechanisms and Robotics | Techniques and Approaches: Mathematical Modeling and Analysis
Design and tests of a planetary non-circular gear train transplanting mechanism for flower plug seedlings
Analysis of force feedback mirror-assisted strategy based on adaptive impedance control
Design and analysis of a two-stage constant-torque flexure hinge (TS-CTFH) based on fixed-rotation constrained circular-arc segments
Design of a magnetorheological (MR) suspension damper for an agricultural tractor seat based on an adaptive neuro-fuzzy inference system (ANFIS) and active disturbance rejection control (ADRC)
Design and validation of a programmable dual-tunnel soft pneumatic origami actuator with a large maximum shrinkage rate for reciprocating motion
An anti-parallelogram ring four-array rolling mechanism with multiple rolling gaits for mobile robots
Gait planning of a 4–5R rolling mechanism based on the planar 6R single-loop chain
A path-planning algorithm for autonomous vehicles based on traffic stability criteria: the AS-IAPF algorithm
Anthropomorphic modular gripper finger actuated by antagonistic wire and shape-memory alloy (SMA) springs
Inverse dynamics and inertia coupling analysis of a parallel mechanism with parasitic motions and redundant actuations
A linkage-type self-adaptive deformable tracked mechanism based on the six-bar mechanism
Research on 3D information collection path planning for hyper-redundant space robots (HSRs)
Design principles and kinematic analysis of a novel spherical 2-degree-of-freedom (DOF) parallel mechanism
Stability analysis and control method of a variable structure detection robot for underground rescue
Fault identification of the vehicle suspension system based on binocular vision and kinematic decoupling
Meshing stiffness characteristics of modified variable hyperbolic circular-arc-tooth-trace cylindrical gears
Gravity compensation and output data decoupling of a novel six-dimensional force sensor
A replaceable-component method to construct single-degree-of-freedom multi-mode planar mechanisms with up to eight links
Optimal design and experiments of a novel bobbin thread-hooking mechanism with RRSC (revolute–revolute–spherical–cylindrical) spatial four-bar linkage
Dynamic modeling and performance analysis of the 2PRU-PUU parallel mechanism
Development of a flexible endoscopic robot with autonomous tracking control ability using machine vision and deep learning
Modeling and control system experiment of a novel series three-axis stable platform
Design and obstacle-crossing analysis of a four-link rocker-suspension planetary exploration robot
A convolutional neural-network-based diagnostic framework for industrial bearing
Design and analysis of a dual-rope crawler rope-climbing robot
Type synthesis of non-overconstrained and overconstrained two rotation and three translation (2R3T) parallel mechanisms with three branched chains
Motion planning and control strategy of a cable-driven body weight support gait training robot
Optimal resource allocation method and fault-tolerant control for redundant robots
Ellipsoid contact analysis and application in the surface conjugate theory of face gears
Adaptive chaos control of a humanoid robot arm: a fault-tolerant scheme
Kinematic and dynamic characteristics' analysis of a scissor multi-rod ring deployable mechanism
Design of a soft bionic elbow exoskeleton based on shape memory alloy spring actuators
Dimensional synthesis of a spherical linkage crank slider mechanism for motion generation using an optimization algorithm
A versatile end effector for grabbing and spreading of flaky deformable object manipulation
Design and kinematics of a lightweight cruciform continuum robot
Modeling and control strategy of a haptic interactive robot based on a cable-driven parallel mechanism
Research on obstacle performance and tipping stability of a novel wheel–leg deformation mechanism
Dynamic modeling and vibration characteristics analysis of parallel antenna
A real-time and accurate detection approach for bucket teeth falling off based on improved YOLOX
Research on structural parameters and kinematic properties of a drill-in granary grain condition detector
Surface modification and tooth contact analysis of variable hyperbolic circular-arc-tooth-trace cylindrical gears
Analysis of the coaxiality–geometric hysteresis model of a rotate vector reducer based on Ansys Adams
Dynamic modeling and experiment of hind leg swimming of beaver-like underwater robot
Spring efficiency assessment and efficient use of spring methods of statically balanced planar serial manipulators with revolute joints only
Structural optimization of a pipe-climbing robot based on ANSYS
Design and analysis of a hollow-ring permanent magnet brake for robot joints
A novel compound topological invariant for isomorphism detection of planar kinematic chains
Varying rate adaptive hybrid position–impedance control for robot-assisted ultrasonic examination system
Design and kinematic analysis of a multifold rib modular deployable antenna mechanism
Design of a transrectal ultrasonic guided prostate low dose rate brachytherapy robot
Bingliang Ye, Xiwei Wang, Tao Tang, Gongjun Zeng, and Yang Zheng
Mech. Sci., 16, 303–316, https://doi.org/10.5194/ms-16-303-2025, https://doi.org/10.5194/ms-16-303-2025, 2025
Short summary
Short summary
To address the problems relating to the low efficiency and high labor intensity of manual operation in transplanting potted flower plug seedlings, an automatic bowl-clamping-type transplanting mechanism with a planetary gear train based on incomplete non-circular gear transmission is proposed.The design of the mechanism combines forward parameter modification (guiding optimization design) and reverse design, providing a reference for solving practical problems in flower seedling transplanting.
Qing Sun, Qingfeng Li, Ningbo Gu, and Jianwei Niu
Mech. Sci., 16, 291–301, https://doi.org/10.5194/ms-16-291-2025, https://doi.org/10.5194/ms-16-291-2025, 2025
Short summary
Short summary
The robot assisting the affected side for mirror trajectory tracking, due to unidirectional transmission of movement information, might result in excessive movement range on the affected side, potentially increasing the risk of secondary injury as the unaffected side cannot perceive the movement status of the affected side. Therefore, this paper proposes a force feedback mirror-assisted strategy based on adaptive impedance control.
Chongxiang Li, Lifang Qiu, Yue Yu, Cuiying Jiang, and Shenyuan Dai
Mech. Sci., 16, 227–236, https://doi.org/10.5194/ms-16-227-2025, https://doi.org/10.5194/ms-16-227-2025, 2025
Short summary
Short summary
This study proposed an analytical model of a fixed-rotation constrained-arc segment. Based on this, a novel two-stage constant-torque bending hinge is designed, and an optimization study is carried out. Finally, the feasibility of the design scheme is verified by theoretical analysis, finite-element analysis, and experiments. The new bending hinge provides a proficient solution for the design of fixtures, joint rehabilitation devices, and human activity assistive devices.
Wei Tao, Bin Chen, Luyang Zhou, Zhixiong Zheng, Jianjin Wu, and Minghao Duan
Mech. Sci., 16, 113–124, https://doi.org/10.5194/ms-16-113-2025, https://doi.org/10.5194/ms-16-113-2025, 2025
Short summary
Short summary
We developed an advanced control system to enhance the comfort of vehicle seats by reducing vibrations. This innovative system combines an adaptive neuro-fuzzy inference system (ANFIS) and active disturbance rejection control (ADRC) to effectively manage the magnetorheological (MR) damper. Our research showed significant improvements in reducing seat vibrations. Moreover, the system's performance has been demonstrated to exceed that of conventional controls.
Rongna Xu, Qiaoling Meng, Qiaolian Xie, Yuxin Zheng, Cuizhi Fei, Vincenzo Parenti Castelli, and Hongliu Yu
Mech. Sci., 16, 61–73, https://doi.org/10.5194/ms-16-61-2025, https://doi.org/10.5194/ms-16-61-2025, 2025
Short summary
Short summary
This paper proposes a novel dual-tunnel soft pneumatic origami actuator to provide a large maximum shrinkage rate for reciprocating motion. A programmed design method is proposed based on the geometric parameter model and stiffness model of the actuator. In comparison to other actuators, this actuator weighs only 5 g, and the force-to-weight ratio is 600. The maximum shrinkage rate of the actuator is 61 %, increasing the potential for lightweight and compact devices.
Zhiyuan Xun, Guanglong Du, Wenbo Zhu, Wei Yu, Changjiang Liu, Jun Wang, and Quanlong Guan
Mech. Sci., 16, 25–40, https://doi.org/10.5194/ms-16-25-2025, https://doi.org/10.5194/ms-16-25-2025, 2025
Short summary
Short summary
This paper presents a ring four-array rolling mechanism consisting of four anti-parallelogram mechanisms with revolute joints. The mechanism is connected by four anti-parallelograms in a looped configuration and has a not-totally-closed ring shape. The mechanism has planar and spherical patterns of locomotion: the planar pattern locomotion includes the parallelogram rolling gait and the anti-parallelogram tumbling gait and the spherical pattern locomotion includes the spherical rolling gait.
Qing Liu, Qianqian Zhang, Shouzhen Kang, Ziyi Pei, Jialei Li, Yezhuo Li, Yue Yan, Yuhao Liang, and Xinyu Wang
Mech. Sci., 15, 633–643, https://doi.org/10.5194/ms-15-633-2024, https://doi.org/10.5194/ms-15-633-2024, 2024
Short summary
Short summary
In this paper, based on the spatial extension design of a planar 6R single-loop chain, a 4–5R rolling mechanism is proposed, and a set of gait analysis and locomotion strategies are planned for the mechanism. The correctness and feasibility of the theoretical analysis are verified through structural dynamics simulation and prototype design. The theoretical and engineering design basis is laid for the research of the new planar single-loop chain robot.
Minqing Zhao, Xuan Li, Yuming Lu, Hongxi Wang, and Shanping Ning
Mech. Sci., 15, 613–631, https://doi.org/10.5194/ms-15-613-2024, https://doi.org/10.5194/ms-15-613-2024, 2024
Short summary
Short summary
Urban traffic congestion, obstacle avoidance, and driving efficiency are significant challenges for driverless-vehicle path planning in urban environments. The traditional artificial potential field (APF) algorithm is inadequate for meeting efficiency and safety requirements in path planning. This paper proposes a new AS-IAPF path-planning algorithm by introducing stability criteria to enhance target accessibility for autonomous vehicles under dynamic and complex traffic conditions.
Longfei Sun, Yiwen Lan, and Binghao Wang
Mech. Sci., 15, 601–611, https://doi.org/10.5194/ms-15-601-2024, https://doi.org/10.5194/ms-15-601-2024, 2024
Short summary
Short summary
In order to better imitate the enveloping–grasping function of human fingers and control the grasping morphology of the fingers, a modular gripper is proposed to be controlled using a combined differential control of wires and shape-memory alloy (SMA) springs, and the gripper can actively adjust the grasping morphology of the fingers according to the characteristics of the shape and contour of the objects to be grasped so as to achieve stable and reliable grasping.
Chen Cheng, Xiaojing Yuan, Yenan Li, and Fanqi Zeng
Mech. Sci., 15, 587–600, https://doi.org/10.5194/ms-15-587-2024, https://doi.org/10.5194/ms-15-587-2024, 2024
Short summary
Short summary
Our research team designed a robotic mechanism inspired by the masticatory system of human beings. It is to be deployed in the food industry, reproducing the chewing behaviors of human beings. Thus, the properties of the newly developed foods can be evaluated in a human-like manner. To facilitate the model-based motion control in real time, a newly developed methodology from the literature is used. Then, the inertia coupling in the joint space control is analyzed.
Kaisheng Zhang, Xuemin Sun, Ruiming Li, Zhiguo Yu, and Biao Yu
Mech. Sci., 15, 541–553, https://doi.org/10.5194/ms-15-541-2024, https://doi.org/10.5194/ms-15-541-2024, 2024
Short summary
Short summary
This paper designs a linkage-type self-adaptive deformable tracked mechanism module in accordance with the multi-loop mechanism. The mechanism has two modes of forward movement and reverse movement, including deformable tracked-type and rocker arm-type, respectively. This kind of mechanism has very good terrain adaptability and can deform through passive self-adaptive obstacles, which has certain application prospects in special terrains.
Guodong Qin, Haoran Zhang, Lei Zheng, Shijie Liu, Quan Chen, Haimin Hu, Deyang Zhang, Yong Cheng, Congju Zuo, and Aihong Ji
Mech. Sci., 15, 531–539, https://doi.org/10.5194/ms-15-531-2024, https://doi.org/10.5194/ms-15-531-2024, 2024
Short summary
Short summary
This paper proposes a path-planning method for 3D information collection on the space station surface via a hyper-redundant space robot (HSR). Based on the active information collection method, the collision-free viewpoint trajectory of the space station surface can be planned. The path planning of the space station surface information collection can then be realized by importing the space station model data and performing weight initialization, stochastic search, and continuous optimization.
Xuechan Chen, Chao Xin, Zhen Zhang, Yu Guo, An Yin, and Ziming Chen
Mech. Sci., 15, 473–486, https://doi.org/10.5194/ms-15-473-2024, https://doi.org/10.5194/ms-15-473-2024, 2024
Short summary
Short summary
In this paper, the design principle of the symmetrical spherical parallel mechanism (SPM) is obtained by analyzing the conditions for symmetrical motion of the mechanism. A series of symmetrical SPMs is designed based on the constraint force provided by the branches. The SPM can realize continuous rotation around any line on the mid-plane that passes through the rotation center of the spherical mechanism. This feature has great potential for application in fields such as rehabilitation robotics.
Hai-bo Tian, Ao Wang, Maolin Lu, Meiting Zhang, Zenan Zhang, Wencai Zhang, and Xin Su
Mech. Sci., 15, 487–500, https://doi.org/10.5194/ms-15-487-2024, https://doi.org/10.5194/ms-15-487-2024, 2024
Short summary
Short summary
In this paper, a variable structure detection robot for underground rescue is designed for the rescue environment of a 225 mm diameter borehole, combined with the leading arm and the deformable tracks. A stability criterion based on the contact force between the robot and the road surface (contact force stability criterion, CFSC) is proposed, and an adaptive stability control system of the robot is established in combination with a neural network.
Hong Wei, Fulong Liu, Guoxing Li, Xingchen Yun, Muhammad Yousaf Iqbal, and Fengshou Gu
Mech. Sci., 15, 445–460, https://doi.org/10.5194/ms-15-445-2024, https://doi.org/10.5194/ms-15-445-2024, 2024
Short summary
Short summary
Vibration measurement technology based on binocular vision and kinematic decoupling is a new method which can effectively extract vertical vibration signal. The proposed method has the advantages of real-time measurement and low cost and overcomes the limitations of traditional measurement methods in error accumulation.
Dengqiu Ma, Bing Jiang, Zhenhuan Ye, and Yongping Liu
Mech. Sci., 15, 395–405, https://doi.org/10.5194/ms-15-395-2024, https://doi.org/10.5194/ms-15-395-2024, 2024
Short summary
Short summary
In the present paper, study on meshing stiffness characteristics of the modified variable hyperbolic circular-arc-tooth-trace cylindrical gears was proposed. The modified tooth surface equation was deduced, and a 3D model was developed. The load tooth contact analysis (LTCA) model was developed. The meshing stiffness calculation method was proposed and verified by the finite-element calculation. The influence of the load and modification parameters on the stiffness was investigated.
Yongli Wang, Ke Jin, Xiao Li, Feifan Cao, and Xuan Yu
Mech. Sci., 15, 367–383, https://doi.org/10.5194/ms-15-367-2024, https://doi.org/10.5194/ms-15-367-2024, 2024
Short summary
Short summary
A new type of parallel six-dimensional force sensor was developed, and artificial neural network technology was used to achieve decoupling of the sensor output data. In addition, a gravity compensation method based on CAD variable geometry is proposed to optimize the performance of the six-dimensional force sensor.
Liangyi Nie, Huafeng Ding, Andrés Kecskeméthy, Kwun-Lon Ting, Shiming Li, Bowen Dong, Zhengpeng Wu, Wenyan Luo, and Xiaoyan Wu
Mech. Sci., 15, 331–351, https://doi.org/10.5194/ms-15-331-2024, https://doi.org/10.5194/ms-15-331-2024, 2024
Short summary
Short summary
Using loop equations and branch graphs, we propose a method to construct single-degree-of-freedom (single-DOF) multi-mode-planar mechanisms (MMPMs), replacing links or components of the singular configuration of planar mechanisms with multi-mode modules. The method is straightforward, visible, and widely applicable to single-DOF MMPMs. We give new design direction and powerful design guidance for the design of MMPMs, along with the available configuration and more choice for the application.
Bingliang Ye, Xu Wang, Mingfeng Zheng, Pengbo Ye, and Weiwei Hong
Mech. Sci., 15, 269–279, https://doi.org/10.5194/ms-15-269-2024, https://doi.org/10.5194/ms-15-269-2024, 2024
Short summary
Short summary
In order to solve the problem that an embroidery machine generally uses a straight needle and rotary shuttle to form a lock stitch, which results in the low supply of bobbin thread and frequent bobbin changes, a bobbin thread-hooking mechanism with spatial four-bar linkage is proposed which can achieve a continuous supply of bobbin thread. We provide a reference for solving this embroidery machine practical problem with a spatial four-bar mechanism optimal design method.
Tianze Sun, Wei Ye, Chao Yang, and Fengli Huang
Mech. Sci., 15, 249–256, https://doi.org/10.5194/ms-15-249-2024, https://doi.org/10.5194/ms-15-249-2024, 2024
Short summary
Short summary
The main contribution of this paper is to establish the dynamic model of the reconfigurable parallel mechanism, a versatile robotic system capable of adapting its configuration to different tasks. The dynamic model facilitates the analysis of the dynamic performance of the mechanism. This comprehensive dynamic model serves as a valuable tool for control algorithm development and the performance optimization of reconfigurable parallel mechanisms in diverse applications.
Sen Qian, Jianxi Zhang, Zongkun Pei, Xiantao Sun, and Zhe Wu
Mech. Sci., 15, 223–236, https://doi.org/10.5194/ms-15-223-2024, https://doi.org/10.5194/ms-15-223-2024, 2024
Short summary
Short summary
A flexible endoscopic robot is designed to solve the problem that it is difficult to maintain a stable visual field in traditional endoscopic surgery. The main contribution of this research is to realize the motion planning and primary–secondary teleoperation control of the flexible endoscope robot under remote center motion constraints on the basis of its structure and select the appropriate deep learning algorithm to complete the autonomous tracking function.
Da Song, Xinlei Xiao, Ji Ma, and Lixun Zhang
Mech. Sci., 15, 209–221, https://doi.org/10.5194/ms-15-209-2024, https://doi.org/10.5194/ms-15-209-2024, 2024
Short summary
Short summary
In this paper, a novel series three-axis stable platform (STSP) is proposed, and its azimuth angle structure, pitch angle structure, roll angle structure, system control scheme, and control strategy are designed. The main function of this stable platform is to isolate the influence of installation carrier movement or external interference and to provide a stable working environment for equipment installed on the stable platform by establishing a stable reference plane.
Zhen Song, Zirong Luo, and Huixiang Xie
Mech. Sci., 15, 137–157, https://doi.org/10.5194/ms-15-137-2024, https://doi.org/10.5194/ms-15-137-2024, 2024
Short summary
Short summary
There are still many meteorite craters and boulders on the surface of Mars and the Moon that cannot be accessed by existing planetary exploration robots. To solve this issue, this paper proposes a four-link rocker-suspension planetary exploration robot that has both the reliability and low complexity of wheeled rovers and competent terrain adaptability and obstacle-crossing performance.
Bowen Yu and Chunli Xie
Mech. Sci., 15, 87–98, https://doi.org/10.5194/ms-15-87-2024, https://doi.org/10.5194/ms-15-87-2024, 2024
Short summary
Short summary
In this study, we introduce an innovative diagnostic framework tailored to industrial bearings that facilitates automated feature extraction and enables end-to-end fault detection. Our validation across multiple bearing vibration datasets confirms the framework's superiority in handling complex and non-stationary signals in industrial environments.
Jinhang Wang, Lairong Yin, Ronghua Du, Long Huang, and Juan Huang
Mech. Sci., 15, 31–45, https://doi.org/10.5194/ms-15-31-2024, https://doi.org/10.5194/ms-15-31-2024, 2024
Short summary
Short summary
A rope-climbing robot (RCR) can reciprocate on a rope. To address poor load capacity and adaptability, this study designs a dual-rope crawler type RCR for use as a new type of transportation equipment in hilly, mountainous, and plateau areas. The crawler rope-climbing mechanism is a combination of a chain drive and the rope-climbing foot. With overhead rope parabolic theory to kinematically analyze the RCR system, the robot motion trajectory model and tilt angle equation are established.
Yu Rong, Xingchao Zhang, Tianci Dou, and Hongbo Wang
Mech. Sci., 14, 567–577, https://doi.org/10.5194/ms-14-567-2023, https://doi.org/10.5194/ms-14-567-2023, 2023
Short summary
Short summary
This paper presents a new method to design a new mechanism with fewer moving joints and greater bearing capacity. These machinery-manufacturing, parts-processing, and other fields have a wide range of application prospects.
Tao Qin, Qianpeng Wang, Wei Su, Chao Wei, Yanduo Zhang, and Jianwei Zhang
Mech. Sci., 14, 413–427, https://doi.org/10.5194/ms-14-413-2023, https://doi.org/10.5194/ms-14-413-2023, 2023
Short summary
Short summary
A cable-driven body weight support gait training robot (C-BWSGTR) was designed to help provide patients with partial body weight support and a stable walking driving force to assist gait rehabilitation training. Overall configuration, kinematic modeling, and motion planning were carried out, and a position servo composite control strategy was designed. Simulation analysis and the prototype experiment verified that the designed control strategy met the requirements of the system.
Yu Rong, Tianci Dou, and Xingchao Zhang
Mech. Sci., 14, 399–412, https://doi.org/10.5194/ms-14-399-2023, https://doi.org/10.5194/ms-14-399-2023, 2023
Short summary
Short summary
Resource coordination and allocation strategies are proposed to reduce the probability of failure by aiming at the problem that the robot cannot continue to work after joint failure. Taking the planar 4R redundant robot as an example, the algorithm control is compared. Based on reasonable modeling and physical verification, the results show that the method of optimal resource coordination and allocation is effective.
Xiaomeng Chu, Yali Liu, and Hong Zeng
Mech. Sci., 14, 305–314, https://doi.org/10.5194/ms-14-305-2023, https://doi.org/10.5194/ms-14-305-2023, 2023
Short summary
Short summary
In the design and processing of face gears, it is not necessary to accurately express the tooth surface with an equation, since it will be difficult to analyze some of the most important and practical features, such as the induced curvature relationship. In this regard, this paper uses the discrete curvature relationship of a spatial gradient curvature ellipsoid to describe the space meshing surface, and it establishes a set of discrete digital conjugate surface meshing principles.
Said Ghani Khan
Mech. Sci., 14, 209–222, https://doi.org/10.5194/ms-14-209-2023, https://doi.org/10.5194/ms-14-209-2023, 2023
Short summary
Short summary
Humanoid robots are stepping into the social environment. However, smooth and safe operation is still a challenge. Faults in robotics, whether mechanical or electrical, are still inevitable. In this work, we present a fault-tolerant scheme for a humanoid robotic arm, to minimize the damage if a joint fails during normal operation or during human–robot interaction or cooperation.
Bo Han, Yuxian Yao, Yuanzhi Zhou, Yundou Xu, Jiantao Yao, and Yongsheng Zhao
Mech. Sci., 14, 193–207, https://doi.org/10.5194/ms-14-193-2023, https://doi.org/10.5194/ms-14-193-2023, 2023
Short summary
Short summary
A double-layer ring truss deployable antenna mechanism is proposed, which is connected by a scissor-like structure. The degrees of freedom, six-dimensional velocity, and acceleration are calculated using spiral theory, and the dynamic model is established. Simulation software is used to verify the simulation, and the prototype is made at a reduced scale. Because the satellite antenna is very important, we decided to study the supporting frame.
Qiaolian Xie, Qiaoling Meng, Wenwei Yu, Rongna Xu, Zhiyu Wu, Xiaoming Wang, and Hongliu Yu
Mech. Sci., 14, 159–170, https://doi.org/10.5194/ms-14-159-2023, https://doi.org/10.5194/ms-14-159-2023, 2023
Short summary
Short summary
This paper presents a novel soft bionic elbow exoskeleton based on shape metal alloy (SMA) actuators (Sobee-SMA). The exoskeleton adopts a bionic design, combining active deformation material SMA and high elastic material rubber band to simulate the contraction and relaxation of the elbow skeletal muscle. According to the static analysis of the human–exoskeleton coupling model and experiments, the exoskeleton provides elbow-assisted motion and ensures the safety of the thermal heating process.
Wei Zhang, Zhen Liu, Wenrui Liu, Jianwei Sun, and He Lu
Mech. Sci., 14, 125–142, https://doi.org/10.5194/ms-14-125-2023, https://doi.org/10.5194/ms-14-125-2023, 2023
Short summary
Short summary
A new method to solve the motion generation problem of a spherical four-bar crank slider rigid-body guidance mechanism is introduced. According to the amplitude and phase of the position output and direction output of the mechanism, the method of establishing the mechanism output characteristic database is given. Then the solution method of size parameters is given. According to the database and solution method, the motion generation is realized.
Yuan Huan, Gongchang Ren, Xiangyu Su, and Weizhi Tian
Mech. Sci., 14, 111–123, https://doi.org/10.5194/ms-14-111-2023, https://doi.org/10.5194/ms-14-111-2023, 2023
Short summary
Short summary
A reconfigurable multi-link mechanism is proposed, and based on the multi-link mechanism and the roller fingertip structure, an end effector is designed to manipulate geometric soft fabrics. The working principle of the reconfigurable multi-link mechanism, the structure and grasping mode of the end effector are introduced in detail, and the kinematics analysis and simulation of the end effector are carried out.
Pan Zhou, Jiantao Yao, Hongyu Zhang, Xuanhao Zhang, Shuaiqi kong, and Kunming Zhu
Mech. Sci., 14, 99–109, https://doi.org/10.5194/ms-14-99-2023, https://doi.org/10.5194/ms-14-99-2023, 2023
Short summary
Short summary
Lightweight and stable continuum robot design is a challenge. We propose a 65 g continuum robot formed using cruciform-arranged elastic sheets. It has low coupling, better bending characteristics in the deformation direction, and a large load capacity in the non-deformation direction, providing a new configuration for lightweight and dexterous continuum robots. Its kinematics model accuracy is experimentally verified. Nucleic acid detection demonstration proves its dexterity and adaptability.
Da Song, Xinlei Xiao, Gang Li, Lixun Zhang, Feng Xue, and Lailu Li
Mech. Sci., 14, 19–32, https://doi.org/10.5194/ms-14-19-2023, https://doi.org/10.5194/ms-14-19-2023, 2023
Short summary
Short summary
The haptic interactive robot based on a cable-driven parallel mechanism studied in this paper is mainly used for interactive training between an astronaut and a virtual environment. This haptic interactive robot can accurately simulate the motion and mechanical characteristics of objects in a microgravity environment and can safely interact with astronauts.
Minghui Zhang and Yiming Su
Mech. Sci., 14, 1–13, https://doi.org/10.5194/ms-14-1-2023, https://doi.org/10.5194/ms-14-1-2023, 2023
Short summary
Short summary
A new type of wheel–leg deformation mechanism, based on an electromagnetic clutch and gear rack transmission mechanism, is designed for moving on complex terrain. The walking model is established to study the kinematics characteristics and obstacle-surmounting performance of the mechanism. The stability cone method is used to evaluate the rollover stability and anti-interference ability in order to ensure the normal operation of the mechanism.
Guoxing Zhang, Jianliang He, Jinwei Guo, and Xinlu Xia
Mech. Sci., 13, 1019–1029, https://doi.org/10.5194/ms-13-1019-2022, https://doi.org/10.5194/ms-13-1019-2022, 2022
Short summary
Short summary
The closed-form dynamics equation of the 1.8 m aperture parallel antenna is established. The relationship between the mechanism's natural frequency, displacement response, and resonance frequency is obtained. Based on the dynamic model, the closed-loop motion control strategy of the parallel antenna mechanism is established. The tracking error of the pitch and azimuth motion of the parallel antenna in the workspace is within ±0.05°.
Jinnan Lu and Yang Liu
Mech. Sci., 13, 979–990, https://doi.org/10.5194/ms-13-979-2022, https://doi.org/10.5194/ms-13-979-2022, 2022
Short summary
Short summary
Aiming at the potential safety problems caused by the looseness of bucket teeth of the electric shovel, we propose an improved YOLOX algorithm. After introducing the dilated CBAM, the deep separable convolution, and model compression, the mAP is decreased by 0.33 %, the detection speed is increased by 11.9 fps, and the model volume is reduced to 29.46 % of the YOLOX model. It provides a theoretical basis and technical support for the development of intelligent mines and mining intelligence.
Qiang Yin, Junpeng Yu, Shaoyun Song, Yonglin Zhang, Gang Zhao, Zhiqiang Hao, and Ao Hu
Mech. Sci., 13, 961–978, https://doi.org/10.5194/ms-13-961-2022, https://doi.org/10.5194/ms-13-961-2022, 2022
Short summary
Short summary
In order to store grain in large warehouses, a process is required that will prevent the effects of mildew and heat. Real-time monitoring of the grain status is needed. Using the information obtained from the monitoring system, corresponding measures were taken for the heating and mildew points in the grain pile. We proposed a drill which is a granary grain condition detector. It can be equipped with temperature, CO2, and humidity sensors and gather information by entering the grain pile.
Yongping Liu and Dengqiu Ma
Mech. Sci., 13, 909–920, https://doi.org/10.5194/ms-13-909-2022, https://doi.org/10.5194/ms-13-909-2022, 2022
Short summary
Short summary
Firstly, the tooth surface modification method based on the parabolic forming blade and cutter inclination was proposed. Next, the modified tooth surface equation was deduced and the 3D reconstruction of the modified tooth surface is realized. Then, the influence of modification parameters on tooth surface curvature characteristics was analysed. Finally, the tooth contact analysis model was established to discuss the influence of modification parameters on the elliptical contact area.
Yongming Liu, Lei Fu, Zhuanzhe Zhao, Qiang Ma, Yujian Rui, and Zhen Zhang
Mech. Sci., 13, 855–866, https://doi.org/10.5194/ms-13-855-2022, https://doi.org/10.5194/ms-13-855-2022, 2022
Short summary
Short summary
The coaxiality–geometric hysteresis model of the RV reducer transmission system is established, and the model is simulated and analyzed with Adams software. The results show that coaxiality is one of the main error factors affecting hysteresis. This research can provide a theoretical basis and reference materials for the measurement and design of RV reducer hysteresis, as well as the design of the RV reducer performance high-precision detection device and its adjustment mechanism.
Gang Chen, Zhenyu Wang, Jiajun Tu, and Donghai Wang
Mech. Sci., 13, 831–842, https://doi.org/10.5194/ms-13-831-2022, https://doi.org/10.5194/ms-13-831-2022, 2022
Short summary
Short summary
In the research and development process of underwater motion control of the beaver-like robot, the hind leg and tail are the main actuators. In order to estimate the driving force of the robot autonomously during underwater movement, we propose this model, which can quickly and easily infer the force of the hind leg on the body. The correctness of this model is verified by experiments and simulations.
Chia-Wei Juang, Chi-Shiun Jhuang, and Dar-Zen Chen
Mech. Sci., 13, 817–830, https://doi.org/10.5194/ms-13-817-2022, https://doi.org/10.5194/ms-13-817-2022, 2022
Short summary
Short summary
This paper proposes a spring efficiency assessment and the efficient use of springs methods for a static spring-balanced manipulator. Gravity is balanced by springs; however, it also contains counter-effects between springs. Conceptually, with fewer counter-effects between springs, there is less burden on the spring system, which means that the springs are used more efficiently. Through adjustment of the springs' attachment and parameters, a method to use springs efficiently is developed.
Yi Zheng, Minghua Liu, Baoshun Li, Guoqing Ma, and Maohua Xiao
Mech. Sci., 13, 725–733, https://doi.org/10.5194/ms-13-725-2022, https://doi.org/10.5194/ms-13-725-2022, 2022
Short summary
Short summary
In order to improve the structural performance of the out-of-pipe pipe-climbing robot, the out-of-pipe pipe-climbing robot is optimized. The structure and size of the robot was optimized. Static and modal analyses were then performed on key robot components and ANSYS was used for topology optimization. It was found the weight of the optimized frame and clamping arm were respectively reduced by 24 % and 20 %, and the maximum stress was respectively reduced by 46 % and 20 %.
Ruoyu Tan, Jieji Zheng, Bin Yu, Baoyu Li, Dapeng Fan, and Xin Xie
Mech. Sci., 13, 687–699, https://doi.org/10.5194/ms-13-687-2022, https://doi.org/10.5194/ms-13-687-2022, 2022
Short summary
Short summary
A novel hollow-ring permanent magnet brake integrated in robot joints is proposed, which allows the brake to require much less axial space and provides more than 1.5 times braking torque for the same volume as the conventional electromagnetic-spring friction brake. A coupled dynamics model of the proposed brake is developed from machine-electric-magnetic aspects. The 3D model of the brake is simulated through finite-element software. The theoretical models are verified through experiments.
Yingxian Wang, Rongjiang Cui, and Jinxi Chen
Mech. Sci., 13, 585–591, https://doi.org/10.5194/ms-13-585-2022, https://doi.org/10.5194/ms-13-585-2022, 2022
Short summary
Short summary
This paper use the topological characteristic constants for isomorphism identification, such as the power value sequence (PVS), least distance matrix sequence (LDMS), and loop number (LN). The fourth PVS, the LDMS, and the LN are compared and arranged in descending order, forming a strong complementary chain. Our results show that solving the problem of the isomorphism identification of the kinematic chain (KC) based on graph theory definition has no advantage in efficiency.
Zhanxin Xie and Zheng Yan
Mech. Sci., 13, 559–575, https://doi.org/10.5194/ms-13-559-2022, https://doi.org/10.5194/ms-13-559-2022, 2022
Short summary
Short summary
Robotic ultrasonic scanning needs to apply an appropriate force for a long time during the acquisition process. Excessive contact force may lead to deformation and even hurt the patient, while insufficient force would lead to poor image quality. We proposed a varying rate hybrid position–impedance control strategy, which can partly play the role of an ultrasound sonographer and serve as a medical assistant to reduce their workload.
Dake Tian, Haiming Gao, Lu Jin, Rongqiang Liu, Yu Zhang, Chuang Shi, and Jiewei Xu
Mech. Sci., 13, 519–533, https://doi.org/10.5194/ms-13-519-2022, https://doi.org/10.5194/ms-13-519-2022, 2022
Short summary
Short summary
Space deployable antenna is a new type of space structure, and one of the key payloads of spacecraft, which is widely used in mobile communication, navigation and remote sensing, deep space exploration, military reconnaissance, and other fields of science and technology and national defense. Aiming at the urgent need for the development of space deployable antenna with large aperture and a high storage rate, a new configuration of a multifold rib modular deployable antenna mechanism is proposed.
Xuesong Dai, Yongde Zhang, Jingang Jiang, Bing Li, and Sihao Zuo
Mech. Sci., 13, 399–409, https://doi.org/10.5194/ms-13-399-2022, https://doi.org/10.5194/ms-13-399-2022, 2022
Short summary
Short summary
Transrectal prostate brachytherapy (BT) can effectively treat prostate cancer. During the operation, doctors need to hold the ultrasound probe for repeated adjustments, which makes it difficult to ensure the efficiency, accuracy, and safety of the operation. We designed an 11 DOF (degrees of freedom) active and passive transrectal BT robot based on the analysis of the transrectal prostate BT process.
Cited articles
Chang, S., Cao, J., Pang, J., Zhou, F., and Chen, W.: Compensation control strategy for photoelectric stabilized platform based on disturbance observation, Aerosp. Sci. Technol., 145, 108909, https://doi.org/10.1016/j.ast.2024.108909, 2024.
Chen, P., Jiang, M., Lv, X., Zhou, H., Yang, D., Zhou, Y., Jin, Z., and Peng, S.: Research on the application of inertially stabilized platform in the dynamic measurement of cold atomic gravimeter, Heliyon, 10, e23936, https://doi.org/10.1016/j.heliyon.2023.e23936, 2024.
Chen, W., Wang, S., Li, J., Lin, C., Yang, Y., Ren, A., Li, W., Zhao, X., Zhang, W., Guo, W., and Gao, F.: An ADRC-based triple-loop control strategy of ship-mounted Stewart platform for six-DOF wave compensation, Mech. Mach. Theory, 184, 105289, https://doi.org/10.1016/j.mechmachtheory.2023.105289, 2023.
Deng, J., Xue, W., Zhou, X., and Mao, Y.: On Dual Compensation to Disturbances and Uncertainties for Inertially Stabilized Platforms, Int. J. Control Autom., 20, 1521–1534, https://doi.org/10.1007/s12555-021-0022-3, 2022.
Fan, L., and Teng, L.: Design and kinematics analysis of 3-DOF ship-borne parallel stabilization platform, Ship Science and Technology, 46, 71–74, https://doi.org/10.3404/j.issn.1672-7649.2024.11.013, 2024.
Gong, Q., Liu, Z., Hu, X., Teng, Y., Li, K., and Han, G.: Robust anti-disturbance fault-tolerant control of ship-board platforms with multiplicative actuator faults and unknown disturbances, Ocean Eng., 286, 115552, https://doi.org/10.1016/j.oceaneng.2023.115552, 2023.
Han, B., Jiang, Y., Yang, W., Xu, Y., Yao, J., and Zhao, Y.: Kinematics characteristics analysis of a 3-UPS/S parallel airborne stabilized platform, Aerosp. Sci. Technol., 134, 108163, https://doi.org/10.1016/j.ast.2023.108163, 2023.
Hunek, W. P., Majewski, P., Zygarlicki, J., Nagi, Ł., Zmarzły, D., Wiench, R., Młotek, P., and Warmuzek, P.: A Measurement-Aided Control System for Stabilization of the Real-Life Stewart Platform, Sensors, 22, 7271, https://doi.org/10.3390/s22197271, 2022.
Jing, C., Ma, X., Du, H., Liu, Y., Liu, C., and Hui, Y.: Adaptive Robust Control for Six-Degree-of-Freedom Electro-Hydraulic Parallel Ship Stabilization Platform, Ijomam, I, 1–12, https://doi.org/10.17683/ijomam/issue18.12, 2024.
Koraaa, M. M., Ghamry, K. A., Abo-Elnor, M. E., and Elsherif, I. A.: Inverse Kinematics Analysis of a 2-DOF Stabilized Platform using Simulink and Simscape, J. Phys. Conf. Ser., 2811, 012003, https://doi.org/10.1088/1742-6596/2811/1/012003, 2024.
Lei, H., Tongzhen, D., Lingbin, S., Qiang, J., and Lifu, W.: Structural Design Key Points and Stability Analysis of Shipborne Self-Stabilizing Platform, in: 2024 4th Asia–Pacific Conference on Communications Technology and Computer Science (ACCTCS), 24–26 February 2024, Shenyang, China, 690–695, https://doi.org/10.1109/ACCTCS61748.2024.00128, 2024.
Liu, J., Cai, C., Song, D., Zheng, J., Guo, X., Sun, X., Hu, Z., and Li, Q.: Power output and platform motion regulation of floating offshore wind turbine using model predictive control based on coupled dynamics model, Ocean Eng., 322, 120451, https://doi.org/10.1016/j.oceaneng.2025.120451, 2025.
Liu, Y., Yuan, H., Xiao, Z., and Xiao, C.: An Offshore Self-Stabilized System Based on Motion Prediction and Compensation Control, Journal of Marine Science and Engineering, 11, 745, https://doi.org/10.3390/jmse11040745, 2023.
Liu, Y., Wang, Q., Qiu, J., Huang, S., and Tao, W.: A 6 Degrees of Freedom Platform for Adjusting Pose Based on 6-PRSS, IJST-TMech. Eng., 49, 897–916, https://doi.org/10.1007/s40997-024-00802-w, 2024.
Lv, Z., Liu, P., Ning, D., and Wang, S.: Anti-Swaying Control Strategy of Ship-Mounted 3-RCU Parallel Platform Based on Dynamic Gravity Compensation, Machines, 12, 209, https://doi.org/10.3390/machines12030209, 2024.
Mei, D. and Yu, Z.-Q.: Disturbance rejection control of airborne radar stabilized platform based on active disturbance rejection control inverse estimation algorithm, Assembly Autom., 41, 525–535, https://doi.org/10.1108/AA-10-2020-0158, 2021.
Pashkov, I. V.: Modification of the Gough–Stewart Platform with Six Degrees of Freedom, J. Mach. Manuf. Reliab., 53, 307–313, https://doi.org/10.1134/S1052618824700237, 2024.
Patra, B., Nag, A., and Bandyopadhyay, S.: Analytical determination of the optimal effective regular workspace of a 6-6 Stewart platform manipulator for a specified orientation workspace, Mech. Mach. Theory, 203, 105791, https://doi.org/10.1016/j.mechmachtheory.2024.105791, 2024.
Qiang, H., Du, L., Liu, K., Zhou, L., and Zeng, S.: Kinematics and Dynamics Modeling of 1T2R Heavy-load Parallel Stabilized Platform with Analytical Solution, Acta Armamentarii, 45, 3960–3969, https://doi.org/10.12382/bgxb.2023.1168, 2024.
Tang, G., Lei, J., Li, F., Zhu, W., Xu, X., Yao, B., Claramunt, C., and Hu, X.: A modified 6-DOF hybrid serial–parallel platform for ship wave compensation, Ocean Eng., 280, 114336, https://doi.org/10.1016/j.oceaneng.2023.114336, 2023.
Tu, Y., Du, J., and Liu, W.: Design and kinematics analysis of 3-DOF ship-borne parallel stabilization platform, Ship Science and Technology, 44, 155–157, https://doi.org/10.3404/j.issn.1672-7649.2022.05.033, 2022 (in Chinese).
Vu, M. T., Alattas, K. A., Bouteraa, Y., Rahmani, R., Fekih, A., Mobayen, S., and Assawinchaichote, W.: Optimized Fuzzy Enhanced Robust Control Design for a Stewart Parallel Robot, Mathematics, 10, 1917, https://doi.org/10.3390/math10111917, 2022.
Ya, J., Dong, R., and Yu, Z.: Control system of shipborne stable platform based on RBF neural network, Ship Science and Technology, 45, 181–185, https://doi.org/10.3404/j.issn.1672-7649.2023.09.040, 2023b.
Ya, T., Du, J., and Li, J.: PTESO based robust stabilization control and its application to 3-DOF ship-borne parallel platform, Ocean Eng., 284, 115202, https://doi.org/10.1016/j.oceaneng.2023.115202, 2023a.
Zhang, Y., Lu, D., Wang, Z., Wang, J., Pan, Q., and Su, S.: Modeling and simulation of six degrees of freedom marine stable platform, in: International Conference on Mechatronic Engineering and Artificial Intelligence (MEAI 2023), 15 December 2024, Shenyang, China, 78, https://doi.org/10.1117/12.3025491, 2024.
Zhao, J., Zhao, T., and Liu, N.: Fractional-Order Active Disturbance Rejection Control with Fuzzy Self-Tuning for Precision Stabilized Platform, Entropy, 24, 1681, https://doi.org/10.3390/e24111681, 2022.
Zhou, Y., She, J., Wang, F., and Iwasaki, M.: Disturbance Rejection for Stewart Platform Based on Integration of Equivalent-Input- Disturbance and Sliding-Mode Control Methods, IEEE/ASME Trans. Mechatron., 28, 2364–2374, https://doi.org/10.1109/TMECH.2023.3237135, 2023.
Short summary
In this paper, a three-axis 6-degree-of-freedom ship stabilization platform is proposed and a fuzzy adaptive proportional–integral–derivative (PID) controller is designed. Comparison with the PID controller shows that the regulation time of PID and fuzzy PID is 7 s and 3.5 s, respectively. The fuzzy adaptive PID controller has high tracking accuracy and stability. Finally, the control user interface of the ship stabilization platform is designed based on Qt Creator.
In this paper, a three-axis 6-degree-of-freedom ship stabilization platform is proposed and a...
